Parts & Accessories
The Wahoo RPM cadence sensor is your sleek little solution for measuring cycling cadence data. It is wireless, magnet-less, lightweight, and easily mounts to your bike's crank arm or to your shoe. Bluetooth Smart and ANT+ dual band technology allows you to connect to and display data on both smartphones and GPS bike computers. Collecting cadence data has never been this easy. - Both ANT+ and Bluetooth Smart capabilities allow for a wireless connection to both smartphones and bike computers. - No tangled wires on your bike to connect the sensor to your device. - It only weighs 7 grams! - Provides accurate cadence data during your ride - (1) mount with double sided 3M tape, or (2) use the silicone sleeve and mount with zip ties. - The RPM can be worn on your shoe for spin classes or use with multiple bikes - Two LED lights show the sensor's device connection (blue) and cadence detection (red) - No charging required! Operates on a coin cell battery for up to 1 years. - RPM cadence sensor will fit with most bikes and frame sizes
Keeps corrosive sweat from reaching your frame. - Cell phone pouch included.
Kurt Kinetic's 12mm Traxle Through-Axle lets you attach your mountain bike to a Kinetic trainer without changing the original skewer. The Kinetic Traxle comes in 3 thread pitches: - T-2101 Coarse: M12 x 1.75mm - T-2102 Medium: M12 x 1.5 - T-2100 Fine: M12 x 1.00mm (Fine XL has the same thread pitch and is a longer version of the fine Traxle)
$17.95 - $19.95
- Replacement belt - Select model based on model/roller size and belt size
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
Connect your PC to CycleOps VirtualTraining.
The Mag Riser Block 3 from Minoura lifts up your front wheel during a training session to be at a natural level. This block fits both MTB and Road bike tire widths. - Fits under front wheel to level the bike to get natural riding on training - Double grooved design fits your narrow or wide ties - Polyethylene material minimizes weight at 1/2 lb. - 8.6D X 4.7W X 2.75H (inches)
The Training Mat is the finishing touch to your training area. Placed between the home trainer and the floor, it improves comfort and protects your home from oil, dirt, and sweat. Plus, it limits the noise produced by training, especially on wooden floors. - Easy to roll up and store away - Dampens vibrations - Easy to clean - Length: 1800mm - Width 900mm
$44.99 - $59.99
The E-Thru Trainer Axle allows the use of a mountain bike in a Tacx trainer. These axles are only suitable for Tacx classic trainers.
Protects the bicycle from sweat and avoids corrosions or rust. - Prevents an accumulation of sweat on the frame and components that would lead to corrosion or affect the finish - Sits above the top-tube and can be adjusted for different bicycles - Washing-machine friendly
Use these axle nuts to put a city or track bike in a Tacx trainer. The available axle nuts are M10x1 (T1415) and 3/8 Shimano Nexus (T1416). For use with Tacx classic trainers only
Look, your child is destined for greatness. We won't dispute that. But, why wait until they can walk for them to rock their awesomeness? If they're crawling, they're ready to explore the world. Attach the Strider Rocking Base to a Strider 12 Bike and get them rocking. The rocking base doesn't just familiarize them with a bike, the rocking motion helps develop their balance, spatial awareness, and core strength. No batteries. No annoying sounds. Just pure, rocking fun. - Compatible with the Strider 12 Classic, Sport, and Pro Balance Bikes - When the Strider 12" Bike is attached this product is intended for ages 6 months – 5 years old for Strider Sport and Pro, and ages 6 months – 3 years for Strider Classic.
The Bkool speed & cadence sensor will make any trainer compatible with the Bkool Simulator. Using ANT+ & Bluetooth Smart wireless transmission, the sensor is also compatible with all ANT+/BLE bike computers and smart phones.
-The cadence sensor attaches to the chain stay on any bike using with plastic ties. -ANT+s wireless transmission technology. -Size: 3 x 3 x 1.5 cm Weight: 50 gr. -Crank arm magnet included.
Misuro B+ is the perfect sensor to enhance your training sessions with Elite home trainers and rollers. This ANT+ and Bluetooth Smart Speed/Power/Cadence sensor monitors indoor training sessions via smartphone, tablet, cycle computer, or compatible GPS devices when installed on an Elite trainer. - Reads data based on the type of trainer used. - Uses ANT+ and Bluetooth Smart protocols that are compatible with many devices. - When paired with the My E-Training Software, it turns your Elite trainer into an advanced digital instrument that displays and manages fundamental training data.
The Elite Thru Axle adapter kit makes Elite trainers compatible with bicycles with 10mm to 12mm diameter through bolts on the rear wheel (lengths from 130mm to 148mm boost). Easy to set up to start right away with your training, this Thru Axle adapter is made from quality material to ensure an immediate setup and great protection to the threads of your bicycle frame. This unit does it all!
The Skyliner is a front wheel support for use with Tacx classic trainers. It raises and supports the front wheel for a natural cycling position and increased stability. It also serves as a handle to carry the trainer.
Give your Tacx trainer the best possible protection for storage and transport with this sturdy trainer bag. It's designed specifically for Tacx trainers and has a separate compartment on the inside for accessories. The double inner layer with foam lining provides optimum protection, minimizing the risk of damage.
Use this ANT+ antenna to connect an ANT+ trainer to your computer. That enables you to use computer software during your training sessions, such as the Tacx Trainer software, Zwift, and TrainerRoad. These programs read the training data transmitted by an ANT+ trainer and can control the trainer. It features a long cable so the receiver can be placed close to the trainer for an optimal reception without loss. The antenna is compatible with all trainers that communicate wirelessly via ANT+.
The Tacx trainer tires have been developed specifically for riding indoors on bike trainers. The special rubber minimizes the risk of overheating, slipping, and wear and tear. They are also quieter than regular rear tires on both road and mountain bikes. Tacx trainer tires are not suitable for outside riding.
The Gel Block is an indispensable accessory for perfecting your position on the bike and provides a more natural feel to your training. - Reduces vibrations on the handlebars for more comfortable training - Non-slip Elastogel insert ensures maximum stability and alignment of the front wheel - Suitable for road and MTB
The Elite Folding Mat increases the comfort of your home cycling setup while protecting the surfaces you train on every day. It's easy to use, store, and transport and can be stored everywhere in your house. Dimensions: 1.8m x .9m
Our Trainer Axle is designed to adapt your Surly MDS/Gnot Boost thru-axle-equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - This axle is for Surly bikes with the MDS/Gnot Boost system. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum, and hard-anodized for rugged durability. - No special tools required. Design allows for wheel installation or removal using your standard 5 mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
The Saris thru axle adapter is designed for indoor use on Saris- and CycleOps-branded trainers only and should not be ridden outdoors. Compatible with current classic series trainers. Not compatible with the JetFluid Pro, SuperMagneto Pro, PowerBeam Pro, or PowerSync trainers. Contact us with trainer compatibility questions. - This adapter is designed to work with bikes that have a 142x12mm or 148x12mm thru axle with 1.0 or 1.75 thread pitch. - The axle is threaded on both sides to fit Syntace and Maxle/ABP style thru axle systems. - Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please reach out to your local bike shop or the bicycle manufacturer directly. - Adapts a thru axle hub bike for a trainer - Only compatible with current basic trainers - Fits most 142-148mm thru axle bikes with 1.0 or 1.75 thread pitch
Universal quick release skewer for placing your bike in the trainer or direct drive. This axle replaces the standard quick release, allowing racing bikes and mountain bikes to be used with Tacx trainers.
TICKR FIT heart rate armband uses optical heart rate technology to provide accurate heart rate and calorie burn data in the most comfortable form factor yet! Equipped with Bluetooth and ANT+ technology to seamlessly pair with fitness apps, smartphones, and GPS bike computers and watches. Worn on the forearm, the TICKR FIT heart rate monitor comes with an adjustable band that is designed for your most grueling workouts including running, cycling, fitness classes, and more. TICKR FIT has water-resistant technology and a rechargeable battery that lasts up to 30 hours. - Dual band technology - Real time heart rate and calorie tracking - Advanced performance material - USB rechargeable battery - LED indicator lights - Two adjustable bands included - Third party app compatibility - Apple watch and apple TV integration
Of course you love your Omnium Trainer, but you’re left wondering how you could possibly love indoor cycling training even more. Easy, our absorbent Sweat Guard is designed to keep your carbon, aluminum and steel frame and components safe from corrosive sweat while mimicking your favorite spin class at home. And because your cycling training plan asks for incredibly intense efforts, the Sweat Guard ensures not a drop of sweat will hit your frame during leg-busting intervals. Add a Floor Mat to your indoor cycling collection and you’ve got a training party! - Ultra absorbent terry cloth material - Protects carbon, aluminum, and steel frames and components - Adjustable to fit most any bike - Simple setup and removal with Velcro handlebar mounts and elastic seatpost strap - Machine washable, cold
The Saris Leveling Block keeps your bike level with your trainer. - Adds stability to your training ride. - For use with any rear wheel-mounted trainer. - Raises front bicycle tire 1.1 inches (2.8 cm) off the ground
- Heavy-duty nylon toe straps with classic style steel buckles - Narrow design fits most cage style pedals - 460mm length
CycleOps' Magnetic Remote Shifter is for use with CycleOps' standard Mag trainers. It allows you to adjust the resistance without leaving the saddle and fits on your stem or handlebars.
Page 1 of 2 Next page